Tin
Tin
@tin
Reputable Member
Joined: Mar 3, 2013
Last seen: Dec 23, 2022
Topics: 17 / Replies: 293
Reply
12 years ago
Forum
Reply
Re: For sale "almost" Gebirgs puttees/Wickelgamaschen

If these are available, I would like to take them at Foy. Can pay in advance if you wish.

12 years ago
Forum
Reply
Re: PPS Kar98 - Mini Review

My mags have been charged since I first got the gun and have all retained gas and are working without issue. I finally got to use mine in a game yest...

12 years ago
Reply
Re: Excitement thread

Yerp, I agree. A tad crazy. A touch too far off. And as the driver, I am hoping this journey is less eventful than the last one.

13 years ago
Reply
Re: Mortar's

What gas is in the moscart? Propelling a lit pyro with a burst of flammable gas is not going to end well, though would be fun to watch... from a dist...

13 years ago
Reply
Re: Rifles , who's got em

ICS Garand at 300fps - Awsome. PPS K98 variable fps Matrix N01 Mk3 (fps to be determined) 2x M1 Carbines circa 330 fps Garand is my go to rifle for U...

13 years ago
Reply
Re: Mountain infantry gun help?

I tried a few pulley systems but failed. So I fitted a cross member below the breech and attached the scissor jack to that. The breech was attached to...

13 years ago
Reply
Re: Mountain infantry gun help?

I used a car scissor jack with a lathe wheel attached to give elevation adjustment on the 25 pounder I built. This worked well and I will probably do ...

13 years ago
Reply
Re: The Garand Belt

Was using my ACM BAR at ROTT. Cracking bit of full auto kit for the money. It did start to wobble a bit, but just needed a few screws threadlocking. M...

13 years ago
Reply
Re: An acute state of sellers remorse

I sold two Tanaka revolvers. Yes I know, a moment of madness. I pestered one of the guys to the point that he sold it back to me a year or so later. ...

13 years ago
Reply
Re: Iron Airsoft/Matrix No.1 Mk 3 SMLE Review

A friend is stripping and refinishing the woodwork for me so I needed to remove all of the metalwork. The nose piece was stuck fast. Heating over a fl...

13 years ago
Reply
Re: Iron Airsoft/Matrix No.1 Mk 3 SMLE Review

My mag was leaking from the joint between the main reservoir and the top section. Removing the two drift pins and two Allen screws will allow the mag ...

13 years ago
Reply
Re: Iron Airsoft/Matrix No.1 Mk 3 SMLE Review

It's no consolation but mine (arrived a few days ago) is the same. The mag has a slight leak that I think I will be able to sort out but the o ring in...

13 years ago
Reply
Re: Video of the the Photos

A few pics can be downloaded here: Hi res colour: Hi res sepia: I think Chris is putting an album together combining the two photographers' pics...

13 years ago
Reply
Re: PPS Kar98 - Mini Review

It will be with me tomorrow but I don't know how much use it will get. BAR and Garand are my main weapons, but I might take it out for an hour or two...

13 years ago
Reply
Re: PPS Kar98 - Mini Review

I had a little play with mine during one of our regular walk on games. Adjusting the FPS to a site friendly 270 (with 0.25 BBs) took only a few minute...

13 years ago
Reply
Re: Afternoon All

Hey fella. Virtually the same for me mate! This has boosted my interest in airsoft so much so that I have sold about a dozen pistols and a number of ...

13 years ago
Reply
Re: PPS Kar98 - Mini Review

Yeah, I figured that once the hop is set, things would improve a bit. I don't have the range in my garden to test fire, so it will have to wait until ...

13 years ago
Page 15 / 16